This video shows you the steps to configure the interfaces of the Cisco Router on a network topology using GNS3.
✅ S U B S C R I B E ► http://goo.gl/8d0iG9
✅ Article ► https://www.sysnettechsolutions.com/en/configure-interface-on-cisco-router/
To configure the Cisco Router's #FastEthernet, #GigabitEthernet, or Serial interfaces basically:
Step 1: First open the #GNS3 program and create a new topology, then add a Cisco Router, Switch, and one virtual machine.
Step 2: Connect all devices in the work area with the wiring.
Step 3: Run your virtual computer on VMware and configure VMnet settings according to the network topology you created.
Step 4: Now open the CLI prompt to assign an IP address to the Cisco Router and open the port and execute the commands in the 2:20 timeframe in order.
Step 5: After performing the above commands, you will see that the operation will be successful when you ping the Router from the virtual machine.
Step 6: To open any interface of the Router, you must use the command no shutdown in that interface.
Step 7: Don't forget to subscribe to our YouTube channel for more videos on Cisco training with GNS3!
────────BEST PRODUCT FOR CISCO TRAINING──────────
✅ Buy ► http://bit.ly/CiscoNetworkingEssentials
───────────────RELATED VIDEOS───────────────
➊ How to Backup Router Config File
➦ https://www.youtube.com/watch?v=rk3ozd-5lJ0
➋ How to Backup Router IOS
➦ https://www.youtube.com/watch?v=85HUMPOR1b8
➌ How to Add L2 Switch
➦ https://www.youtube.com/watch?v=vWvXKXas8WA
➍ How to Add L3 Switch
➦ https://www.youtube.com/watch?v=rxt_qPOECW0
➎ How to Configure DHCP
➦ https://www.youtube.com/watch?v=jPnfCV9Xel0
───────────────FOLLOW US───────────────────
✔ Facebook
➦ https://www.facebook.com/SysnettechSolutions/
✔ Twitter
➦ https://twitter.com/SysnettechS/
✔ Pinterest
➦ https://www.pinterest.com/SysnettechS/
✔ Instagram
➦ https://www.instagram.com/sysnettech_solutions/
✔ LinkedIn
➦ https://linkedin.com/in/tolqabaqci/
███████████████████████████████████████████
✅ S U B S C R I B E ► http://goo.gl/8d0iG9
✅ Article ► https://www.sysnettechsolutions.com/en/configure-interface-on-cisco-router/
To configure the Cisco Router's #FastEthernet, #GigabitEthernet, or Serial interfaces basically:
Step 1: First open the #GNS3 program and create a new topology, then add a Cisco Router, Switch, and one virtual machine.
Step 2: Connect all devices in the work area with the wiring.
Step 3: Run your virtual computer on VMware and configure VMnet settings according to the network topology you created.
Step 4: Now open the CLI prompt to assign an IP address to the Cisco Router and open the port and execute the commands in the 2:20 timeframe in order.
Step 5: After performing the above commands, you will see that the operation will be successful when you ping the Router from the virtual machine.
Step 6: To open any interface of the Router, you must use the command no shutdown in that interface.
Step 7: Don't forget to subscribe to our YouTube channel for more videos on Cisco training with GNS3!
────────BEST PRODUCT FOR CISCO TRAINING──────────
✅ Buy ► http://bit.ly/CiscoNetworkingEssentials
───────────────RELATED VIDEOS───────────────
➊ How to Backup Router Config File
➦ https://www.youtube.com/watch?v=rk3ozd-5lJ0
➋ How to Backup Router IOS
➦ https://www.youtube.com/watch?v=85HUMPOR1b8
➌ How to Add L2 Switch
➦ https://www.youtube.com/watch?v=vWvXKXas8WA
➍ How to Add L3 Switch
➦ https://www.youtube.com/watch?v=rxt_qPOECW0
➎ How to Configure DHCP
➦ https://www.youtube.com/watch?v=jPnfCV9Xel0
───────────────FOLLOW US───────────────────
➦ https://www.facebook.com/SysnettechSolutions/
➦ https://twitter.com/SysnettechS/
➦ https://www.pinterest.com/SysnettechS/
➦ https://www.instagram.com/sysnettech_solutions/
➦ https://linkedin.com/in/tolqabaqci/
███████████████████████████████████████████
- Category
- Routers and Switches
Be the first to comment